MARK WILLIAMS DANA 60™ COMPONENTS FOR OFF-ROAD
| ||||||||
1410 Series 29 Spline Pinion Yoke
Uses 1410 series U joint. "B" = 3.720" Manufactured from high strength heat treated 4140 steel, giving over twice the tensile strength of OEM.
Used with: | ![]() | 1350 Series 29 Spline Pinion Yoke
Uses 1350 series U joint. "B" = 3.0313" Manufactured from high strength heat treated 4340 steel. Also works with Viper Dana 44™.
Used with: | ![]() | |||||
![]() | ![]() | ![]() | ||||||
35 Spline Lightweight Steel Spool
Manufactured from through hardened 4140 high strength steel. Proper housing ends are required. | ![]() | 40 Spline Lightweight Steel Spool
MW 40-spline allows the largest and strongest axle available for the Dana 60. Due to the large spline, 58505 wheel bearings and proper housing ends are required For use with 4 series gears, (4.56 to 7.17 Dana Spicer Manufactured gears) (4.10 to 7.17 other manufacturers' gears). Manufactured from through hardened 4140 high strength steel. | ![]() | 40 Spline Aluminum Spool
MW 40-spline aluminum spool allows the super light gun drilled axles in the Dana 60™ rear. Due to the large spline, 58505 wheel bearings and proper housing ends are required for use with 4 series gears (4.56 to 7.17 Dana™ gear) (4.10 to 7.17 other manufacturers' gear). Manufactured from aluminum forgings. | ||||
![]() | ![]() | ![]() | ||||||
Spool Bearing Kit
Timken bearings for all MW Dana 60™ type spools or stock carriers. | ![]() | Pinion Bearings (Set)
Timken bearings for all Dana 60™ type rears. | ![]() | Ring Gear Bolt Kit
Original Equipment bolts. 1/2"-18, 12 point 9/16" hex, .500" grip length (set of 12) | ||||
![]() | ![]() | ![]() | ||||||
Replacement Main Cap
Made from from billet steel with an increased cross section and heat treated grade 8 hardware (included). Requires precision measuring of the cap bore and milling of cap parting line to install. Normally, only the driver’s side cap has to be replaced. | ![]() | 9310 Pro Gears
9 3/4" ring gear, 1.626" diameter pinion stem, 29 spline pinion. Browse Pro Gears
8620 Street Gears
9 3/4" ring gear, 1.626" diameter pinion stem, 29 spline pinion. Browse Street Gears | ![]() | Installation Kit
Contains all of the parts required for a complete ring and pinion installation. Includes pinion and carrier shims, pinion seal, preload shim, ring gear bolts, pinion nut, cover gasket, gear marking compound, and brush. Timken® bearings and races are supplied for the pinion and carrier. | ||||
![]() | ![]() | |||||||
Pinion Depth Shim Kit
Includes pinion depth shims, pre-load shims, spool shims, gasket, pinion nut and washer. | ![]() | Pinion Seal - p/n 56904
Pinion Nut - p/n 56902
Pinion Washer - p/n 30275 | ![]() | Center Section Alignment Rings
Dana 60™, 3.812" O.D. (pr) - p/n 305 Ford 9", 3.250" O.D. (pr) - p/n 306 | ||||
![]() | ![]() | ![]() |
29 spline, for 1410 series U joint. "B"= 3.720"
3/8" diameter bolts with nuts and washers. Set of 8.
3/8" diameter bolts with nuts and washers. Set of 10.
Dana 60, 3.812" O.D. (pr)
Ford 9", 3.250" O.D. (pr)
Complete Dana 60 rearend assembly with locker (less brakes)
MW 35-spline, Lightweight for Dana 60™
MW 40-spline, for Dana 60™
MW 40-spline, Lightweight for Dana 60™.
29 spline, for 1350 u-joint. "B"=3-1/32"
Dana 60™, 35 Spline locker for 4 series gears
Powr-Lok™ Axle gear for Dana 60™ with 35 splines (ea)